button (93) * Do not directly touch these parts. ** Do not cover this part during movie recording. 16 Sides/Bottom Preparing the camera A REMOTE terminal · When connecting the RMS1AM/RM-L1AM Remote Commander (sold separately) to the camera, insert the plug of the Remote Commander into the REMOTE terminal, aligning the guide of the plug with the guide of the REMOTE terminal. Make sure that the cord of the Remote Commander faces forward. B Hooks for shoulder strap (32) C HDMI terminal (136) D · Use a tripod with a screw length of less than 5.5 mm (7/32 inch). You will be unable to firmly secure the camera to tripods having screws longer than 5.5 mm (7/32 inch), and may damage the camera. G Memory card insertion slot (21) H Battery/memory card cover (21) I Connection plate cover (USB) terminal (164) · When an external microphone is connected, the internal microphone is turned off automatically. When the external microphone is a plugin-power type, the power of the microphone is supplied by the camera. E Microphone jack F Tripod receptacle · For using the AC-PW20 AC Adaptor (sold separately) Be careful not to catch the cord of the AC Adaptor in the cover when you close the cover. 17 Lens DT 18-55mm F3.5-5.6 SAM (Supplied with the SLT-A35K/A35Y) DT 55-200mm F4-5.6 SAM (Supplied with the SLT-A35Y) A Focusing ring B Zoom ring C Focal-length scale D Focal-length index E Lens contacts F Focusing mode switch G Mounting index · The DT 18-55mm F3.5-5.6 SAM/DT 55-200mm F4-5.6 SAM are designed for Sony Amount cameras (models equipped with an APS-C sized image sensor). You cannot use these lens on 35mm-format cameras. · For the lenses other than DT 1855mm F3.5-5.6 SAM/DT 55200mm F4-5.6 SAM, refer to the operating instructions supplied with the lens. 18 Charging the battery pack When using the camera for the first time, be sure to charge the NP-FW50 "InfoLITHIUM" battery pack (supplied). The "InfoLITHIUM" battery pack can be charged even when it has not been fully depleted. It can also be used when it has not been fully charged. 1 Insert the battery pack onto the battery charger. Push the battery pack until it clicks. Preparing the camera 2 Connect the battery charger to the wall outlet (wall socket). Light on: Charging Light off: Charge completed · The CHARGE lamp turns off when charging is finished. · Time required to charge a fully depleted battery pack at a temperature of 25°C (77°F) is about 250 minutes. For the U.S.A and Canada Plug CHARGE lamp For countries/regions other than the U.S.A. and Canada CHARGE lamp Power cord (mains lead) 19 Notes · The charging time differs depending on the remaining capacity of the battery back or charging conditions. · We recommend charging the battery pack in an ambient temperature of between 10 to 30°C (50 to 86°F). You may not be able to efficiently charge the battery pack outside of this temperature range. · Connect the battery charger to the nearest wall outlet (wall socket). · Do not try to charge the battery pack again right after it has been charged, or when it has not been used after being charged. Doing so will affect the performance of the battery pack. · Do not charge any battery pack other than the "InfoLITHIUM" W series battery pack in the battery charger (supplied) with your camera. Batteries other than the specified kind may leak, overheat, or explode if you attempt to charge them, posing a risk of injury from electrocution and burns. · When the CHARGE lamp flashes, this may indicate a battery error or that a battery pack other than the specified type has been installed. Check that the battery pack is the specified type. If the battery pack is the specified type, remove the battery pack, replace it with new one or another one and check if the battery charger operates correctly. If the battery charger operates correctly, a battery error may have occurred. · If the battery charger is dirty, charging may not be performed successfully. Clean the battery charger with dry cloth, etc. To use your camera abroad -- Power sources You can use your camera and the battery charger and the AC-PW20 AC Adaptor (sold separately) in any country or region where the power supply is within 100 V to 240 V AC, 50/60 Hz. Note · Do not use an electronic voltage transformer, as this may cause a malfunction. 20 Inserting the battery pack/memory card (sold separately) 1 While sliding the cover open lever, open the cover. Preparing the camera 2 Firmly insert the battery pack all the way while pressing the lock lever with the tip of the battery. Lock lever 3 Insert a memory card. · With the notched corner facing as illustrated, insert the memory card until it clicks into place. Ensure the notched corner faces correctly. 4 Close the cover. 21 Available memory cards · Only "Memory Stick PRO Duo" media, "Memory Stick PRO-HG Duo" media, SD memory cards, SDHC memory cards and SDXC memory cards can be used with this camera. A MultiMediaCard cannot be used with this camera. However, proper operation cannot be guaranteed for all memory cards functions. · The "Memory Stick PRO Duo" media and "Memory Stick PRO-HG Duo" media are referred to as the "Memory Stick PRO Duo" media and the SD memory card, SDHC memory card and SDXC memory card are referred to as the "SD card" in this Instruction Manual. · For recording movies, it is recommended that you use following memory cards. ­ (Mark2) ("Memory Stick PRO Duo" media (Mark2)) ­ ("Memory Stick PRO-HG Duo" media) ­ SD memory card, SDHC memory card, SDXC memory card (Class 4 or more) · Images recorded on an SDXC memory card cannot be imported to or played on computers or AV devices that are not compatible with exFAT. Make sure that the device is compatible with exFAT before connecting it to the camera. If you connect your camera to an incompatible device, you may be prompted to format the card. Never format the card in response to this prompt, as doing so will erase all data on the card. (exFAT is the file system used on SDXC memory cards.) To remove the battery pack Turn off the camera and slide the lock lever in the direction of the arrow. Be careful not to drop the battery pack. Lock lever 22 To remove the memory card Check that the access lamp is not lit, then open the cover, and push the memory card once. Access lamp Preparing the camera To check the remaining battery level Check the level with the following indicators and percent figures displayed on the screen. "Battery exhausted." High Low You cannot shoot any more pictures. Battery level What is an "InfoLITHIUM" battery pack? An "InfoLITHIUM" battery pack is a lithium-ion battery pack that has functions for exchanging information related to operating conditions with your camera. Using the "InfoLITHIUM" battery pack, the remaining battery time in percent figures is displayed according to the operating conditions of your camera. Notes on using the battery pack · The displayed level may not be correct under certain circumstances. · Do not expose the battery pack to water. The battery pack is not waterresistant. · Do not leave the battery pack in extremely hot places, such as in a car or under direct sunlight. 23 Effective use of the battery pack · Battery performance decreases in low temperature surroundings. So, the time that the battery pack can be used is shorter in cold places and the speed of continuous shooting slows down. We recommend that you put the battery pack in a pocket close to your body to warm it up, and insert it in your camera immediately before you start shooting. · The battery pack will run out quickly if you use the flash frequently, use continuous shooting often, brighten the LCD monitor, or turn the camera on and off frequently. Battery life · The battery life is limited. Battery capacity decreases little by little as you use it more and more, and as time passes. If the battery operating time seems shortened considerably, a probable cause is that the battery pack has reached the end of its life. Buy a new battery pack. · The battery life varies according to how it is stored and the operating conditions and environment in which each battery pack is used. How to store the battery pack If the battery pack is not to be used for a long time, charge it and then fully use it up once a year on your camera before storing the battery pack in a dry, cool place to prolong the battery life. Notes on using memory cards · Do not strike, bend or drop the memory card. · Do not use or store the memory card under the following conditions: ­ High temperature locations such as the hot interior of a car parked in direct sunlight. ­ Locations exposed to direct sunlight. ­ Humid locations or locations with corrosive substances present. · The memory card may be hot just after it has been used for a long time. Be careful when you handle it. · When the access lamp is lit, do not remove the memory card or the battery pack, or turn off the power. The data may be corrupted. · Data may be damaged if you place the memory card near stronglymagnetized material or use the memory card in a static-prone or electrically noisy environment. 24 · We recommend backing up important data, such as to a hard disk of a computer. · When you carry or store the memory card, put it in the case supplied with it. · Do not expose the memory card to water. · Do not touch the terminal section of the memory card with your hand or a metal object. · When the write-protect switch of a memory card is set to the LOCK position, you cannot perform operations, such as recording or deleting images. · The memory cards formatted with a computer are not guaranteed to operate with this camera. Be sure to format the memory cards using the camera. · Data read/write speeds differ depending on the combination of the memory cards and the equipment used. · Do not press down hard when you write down on the memo area. · Do not attach a label on the memory cards themselves. · Do not disassemble or modify the memory cards. · Do not leave the memory cards within the reach of small children. They might accidentally swallow it. Preparing the camera 25 Notes on the "Memory Stick" media used with the camera The types of "Memory Stick" media that can be used with this camera are listed in the table below. However, proper operation cannot be guaranteed for all "Memory Stick PRO Duo" media functions. "Memory Stick PRO Duo" media*1*2*3 "Memory Stick PRO-HG Duo" media*1*2 "Memory Stick Duo" media Available with your camera Unavailable with your camera "Memory Stick" media and "Memory Stick PRO" media Unavailable with your camera *1 This is equipped with MagicGate function. MagicGate is copyright protection technology that uses encryption technology. Data recording/playback that requires MagicGate functions cannot be performed with this camera. *2 Supports high-speed data transfer using a parallel interface. *3 When using "Memory Stick PRO Duo" media to record movies, only those marked with Mark2 can be used. Notes on using "Memory Stick Micro" media (sold separately) · This product is compatible with "Memory Stick Micro" media ("M2"). "M2" is an abbreviation for "Memory Stick Micro" media. · To use a "Memory Stick Micro" media with the camera, be sure to insert the "Memory Stick Micro" media into an "M2" Adaptor as large as of Duo size. If you insert a "Memory Stick Micro" media into the camera without an "M2" Adaptor as large as of Duo size, you might not be able to remove it from the camera. · Do not leave the "Memory Stick Micro" media within the reach of small children. They might accidentally swallow it. 26 Attaching a lens 1 Remove the body cap from the camera, the packaging lid from the rear of the lens. · When changing the lens, quickly change the lens away from dusty locations so as to keep dust or debris from getting inside the camera. · When shooting, remove the front lens cap from the front of the lens. Front lens cap Preparing the camera Body cap Packaging lid 2 Mount the lens by aligning the orange index marks on the lens and camera. Orange index marks 3 Turn the lens clockwise until it clicks into the locked position. · Be sure to put the lens on straight. Notes · When attaching a lens, do not press the lens release button. · Do not use force when attaching a lens. · E-mount lenses are not compatible with this camera. · When you use a lens for which a tripod socket is provided, attach the lens onto the tripod using the tripod socket provided to help balance the weight of the lens. · When you carry the camera with the lens attached, make sure to hold both the camera and the lens steadily. 27 · Do not hold by any part of the lens that protrudes when zooming or focusing. To remove the lens 1 Press the lens release button all the way in and turn the lens counterclockwise until it stops. Lens release button 2 Attach the caps to the front and rear of the lens and the body cap to the camera. · Before you attach them, remove dust from them. · A rear lens cap is not supplied with the DT 18-55mm F3.5-5.6 SAM Lens Kit. When you store the lens without attaching it to the camera, purchase the Rear Lens Cap ALC-R55. To attach a lens hood It is recommended that you use a lens hood to reduce flare and ensure maximum image quality. Fit the hood into the mount on the end of the lens barrel and rotate the hood clockwise until it clicks. · A lens hood is not included with the DT 18-55mm F3.5-5.6 SAM. You can use the ALC-SH108 (sold separately). · When using a built-in camera flash, make sure to remove the lens hood to avoid blockage of the flash light. · When storing, turn over the lens hood and place it onto the lens backwards. 28 Note on changing the lens When changing the lens, if dust or debris gets inside the camera and adheres to the surface of the image sensor (the part that acts as the film), it may appear as dark spots on the image, depending on the shooting environment. The camera is equipped with an anti-dust function to prevent dust from adhering to the image sensor. However, quickly change the lens away from dusty locations when attaching/removing a lens. Preparing the camera If dust or debris adheres to the image sensor Clean the image sensor using [Cleaning Mode] in the (page 37). Setup menu 29 Preparing the camera Setting up the date When you turn the camera on for the first time, the date/time setup screen appears. 1 Set the power switch to ON to turn the camera on. The screen used for setting date and time appears. · To turn the camera off, set it to OFF. 2 Verify that [Enter] is selected on the LCD monitor, then press the center of the control button. 3 Select your area with b/B on the control button, then press the center of the control button. 4 Select each item with b/B and set the numeric value with v/V. [Daylight Svg.:]: Turns on or off the daylight saving time setting. [Date Format:]: Selects the format to display date. · Midnight is indicated as 12:00 AM, and noon as 12:00 PM. 30 5 Repeat step 4 to set other items, then press the center of the control button. 6 Verify that [Enter] is selected, then press the center of the control button. To cancel the date/time setting operation Press the MENU button. To set up the date/time again When you turn the camera on for the first time, the date/time setup screen appears automatically. The next time, set up the date and time from the menu. Preparing the camera MENU button t 1 t [Date/Time Setup] To set up the area again You can set the area where you are using the camera. This allows you to set the local area when you use the camera abroad. MENU button t 1 t [Area Setting] Maintaining the date and time setting This camera has an internal rechargeable battery for maintaining the date and time and other settings regardless of whether the power is on or off, or the battery is installed or not. For details, see page 192. Adjusting the focus of the finder (diopter adjustment) Adjust the diopter-adjustment dial to your eyesight until the display appears clearly in the viewfinder. · Training the camera on a light allows you to adjust the diopter easily. Note · The dioptic adjustment attachment (sold separately) cannot be used with this camera. 31 Using the accessories supplied This section describes how to use the shoulder strap and eyecup. The other accessories are described in the following pages. · Rechargeable battery pack (page 19) · Battery charger (page 19) · Power cord (mains lead) (not supplied in the U.S.A. and Canada) (page 19) · USB cable (page 164) · CD-ROM (page 160) Attaching the shoulder strap Attach both ends of the strap onto the camera. 32 Removing the eyecup When attaching the FDA-A1AM Angle Finder (sold separately) to the camera, remove the eyecup. Carefully slide the eyecup off by pushing on each side of the eyecup. · Put your fingers under the eyecup, and slide it upward. Preparing the camera Note · The Magnifier and Magnifying Eyepiece cannot be used with this camera. 33 Checking the number of recordable images Once you insert a memory card into the camera and set the power switch to ON, the number of images that can be recorded (should you continue to shoot using the current settings) is displayed on the screen. Notes · When "0" (the number of recordable images) flashes in yellow, the memory card is full. Replace the memory card with another one, or delete images in the current memory card (page 134). · When "NO CARD" (the number of recordable images) flashes in yellow, it means no memory card has been inserted. Insert a memory card. The number of images that can be recorded on a memory card The table shows the approximate number of images that can be recorded on a memory card formatted with this camera. The values are defined using Sony standard memory cards for testing. The values may vary depending on the shooting conditions and the type of memory card used. Image: Size: L 16M Image: Aspect Ratio: 3:2* "Memory Stick PRO Duo" Capacity Size Standard Fine RAW & JPEG RAW 2GB 386 270 74 106 4GB 781 548 154 220 8GB 1587 1116 319 452 (Units: Images) 16GB 3239 2279 657 928 32GB 6406 4510 1304 1840 * When [Image: Aspect Ratio] is set to [16:9], you can record more images than the numbers shown in the table above (except when [RAW] is selected). 34 The number of images that can be recorded using a battery pack The approximate number of images that can be recorded is as follows when you use the camera with the battery pack (supplied) at full capacity. Note that the actual numbers may be less than those indicated depending on the conditions of use. With the flash LCD monitor mode Viewfinder mode Approx. 440 images Approx. 420 images Without the flash Approx. 480 images Approx. 460 images Preparing the camera · The number is calculated with a battery pack at full capacity and in the following situation: ­ At an ambient temperature of 25°C (77°F). ­ Using the battery pack that is charged for an hour after the CHARGE lamp goes out. ­ Using Sony "Memory Stick PRO Duo" media (sold separately). ­ [Image: Quality] is set to [Fine]. ­ [Autofocus Mode] is set to [Automatic AF]. ­ Shooting once every 30 seconds. ­ The power turns on and off once every ten times. · About the number of images you can shoot when the flash is used: ­ The flash strobes once every two times. ­ The measurement method is based on the CIPA standard. (CIPA: Camera & Imaging Products Association) 35 Cleaning Cleaning the camera · Do not touch the inside of the camera, such as lens contacts, or the mirror. Since dust on the mirror or around the mirror may affect the images or the performance of the camera, blow the dust away using a commercially available blower*. For details on cleaning the image sensor, see the next page. * Do not use a spray blower. Using one may cause a malfunction. · Clean the camera surface with a soft cloth slightly moistened with water, then wipe the surface with a dry cloth. Do not use the following as they may damage the finish or the casing. ­ Chemical products such as thinner, benzine, alcohol, disposable cloths, insect repellent, sunscreen or insecticide, etc. ­ Do not touch the camera with the above on your hand. ­ Do not leave the camera in contact with rubber or vinyl for a long time. Cleaning the lens · Do not use a cleaning solution containing organic solvents, such as thinner, or benzine. · When cleaning the lens surface, remove dust using a commercially available blower. In case of dust that sticks to the surface, wipe it off with a soft cloth or tissue paper slightly moistened with lens cleaning solution. Wipe in a spiral pattern from the center to the outside. Do not spray lens cleaning solution directly onto the lens surface. 36 Cleaning the image sensor If dust or debris enters the camera and adheres to the image sensor (the part that acts as the film), it may appear as dark spots on the photo image, depending on the shooting environment. If there is dust on the image sensor, clean the image sensor following the steps below. Notes · Cleaning cannot be performed when the battery level is 50% or less. · The camera starts beeping if the battery pack becomes low during cleaning. Stop cleaning immediately and turn the camera off. The use of an AC-PW20 AC Adaptor (sold separately) is recommended. · The cleaning should be completed quickly. · Do not use a spray blower because it may scatter water droplets inside the camera body. Preparing the camera To clean the image sensor automatically using the cleaning mode of the camera 1 Confirm that the battery is fully charged (page 23). 2 Press the MENU button, then select 2 with b/B on the control button. MENU button 3 Select [Cleaning Mode] with v/V, then press the center of the control button. 37 4 Select [Enter] with v, and press the center of the control button. The image sensor vibrates for a short time, and eliminates dust from the sensor. 5 Turn off the camera. To clean the image sensor using a blower If another cleaning is needed after using the cleaning mode, clean the image sensor using a blower following the steps below. 1 Perform the cleaning operation described in steps 1 to 4 of "To clean the image sensor automatically using the cleaning mode of the camera." 2 Detach the lens (page 28). 3 Push the V mark on the mirror lock lever with a finger to lift up the mirror. · Be careful not to touch the surface of the mirror. Mirror lock lever 38 4 Use the blower to clean the image sensor surface and the surrounding area. · Do not touch the image sensor with the tip of the blower and do not put the tip of a blower into the cavity beyond the mount. · Hold the camera's face downward to prevent the dust from resettling in the camera. Complete the cleaning quickly. · Also clean the back of the mirror using a blower. Preparing the camera 5 After the cleaning is finished, lower the mirror with a finger until it clicks. · Lower the frame of the mirror back down with a finger. Be careful not to touch the surface of the mirror. · Lower the mirror down until it locks firmly. 6 Attach the lens and turn the camera off. · Confirm that the mirror is locked down firmly when you attach the lens. Notes · After the cleaning is finished, confirm that the mirror is locked down firmly when you attach the lens. Otherwise, the lens may be scratched or this may be the cause of additional trouble. Also, if the mirror is not locked down firmly, the autofocus does not work during shooting. · You cannot shoot while the mirror is lifted up. 39 Before your operation Screen indicators Switching the screen mode between the LCD monitor and the electronic viewfinder When you look into the viewfinder, the viewfinder mode is activated, and when you take your face away from the viewfinder, the screen mode returns to the LCD monitor mode. You can also switch the screen mode using the FINDER/LCD button. FINDER/LCD button Viewfinder LCD monitor To focus on a subject quickly using the viewfinder When you look into the viewfinder, the subject located in the AF area comes into focus automatically (Eye-Start AF). MENU button t 1 t [Eye-Start AF] t [On] When the FDA-A1AM Angle Finder (sold separately) is attached to the camera, setting [Eye-Start AF] to [Off] is recommended because the eyepiece sensors located below the viewfinder may be activated. 40 Switching the recording information display (DISP) Each time you press DISP on the control button, the recording information display changes as follows. The status of the screen in the viewfinder changes as follows ("Recording information on" (For Live View) is skipped). You can switch the screen in the viewfinder separately from the screen on the LCD monitor. Graphic Display Recording information on (For Live View) Recording information off Before your operation Graphic Display The Graphic Display shows the shutter speed and aperture value as graphs, and clearly illustrates how the exposure works. The pointers on the shutter speed indicator and aperture indicator indicate the current value. When the exposure is adjusted, the position of the pointers follows the setting value. Aperture value Shutter speed Recording information display (For viewfinder) You can switch the "Recording information on" display on the LCD monitor to a screen that is suitable for shooting when you look into the viewfinder. The screen in the viewfinder is for Live View. 41 MENU button t 2 t [Display Rec. Data] t [For viewfinder] Each time you press DISP on the control button, the screen changes as follows. Graphic Display Recording information display (For viewfinder) Recording information off To turn off indication of the shutter speed, aperture value, EV scale, and SteadyShot scale in the viewfinder When you turn off the recording information, you can also turn off the indication of the shutter speed, aperture value, EV scale, and SteadyShot scale. MENU button t operating] 2 t [Sets display in finder] t [When · The shutter speed, aperture value, EV scale, and SteadyShot scale will be displayed only while the exposure is being adjusted. 42 Recording information display (Graphic Display/Recording information (For Live View)) Graphic Display Recording information display (For Live View) Before your operation A Display P ASM Indication Exposure mode (60 ­ 84) Display Indication Image quality of still images (141) Image size of movies (141) 100% Remaining battery (23) Overheating warning (189) Memory card (21) 100 Remaining number of recordable images (34) Image size of still images (140)/Aspect ratio of still images (141)/Image size of panoramic images (140) Database file full (189)/ Database file error (189) Camera shake warning (58) No audio recording of movies (87) 43 B Display Indication Spot metering area (108) AF area (93) Shutter speed indicator (79) Aperture indicator (76) C Display REC 0:12 z 1/250 F3.5 Indication Recording time of the movie (m:s) Focus (90) Shutter speed (79) Aperture (76) EV scale (82, 122) AE lock (103) SteadyShot scale (58) D Display Indication Drive mode (119) Display Indication Smile Detection Sensitivity indicator (97) E Display Indication ISO sensitivity (109) Metering (108) Flash compensation (106) AWB White balance (Auto, Preset, Custom, Color temperature, Color filter) (115) D-Range Optimizer (110)/Auto HDR (111) Creative Style (113) 7500K G9 Flash mode (99)/Red-eye reduction (101) Focus mode (92) AF area (93) Face Detection (96) Smile Shutter (97) 44 Recording information display (For viewfinder) See pages in parentheses for details of operation. In AUTO, AUTO+, or Scene Selection mode In Tele-zoom Continuous Advance Priority AE/P/A/S/M mode Before your operation A Display PASM Indication Exposure mode (60 ­ 84) Display Indication No audio recording of movies (87) 100% Remaining battery (23) B Display Indication Flash mode (99)/Red-eye reduction (101) Drive mode (119) Memory card (21) 100 Remaining number of recordable images (34) Image size of still images (140)/Aspect ratio of still images (141) Image quality of still images (141) Focus mode (92) Face Detection (96) Smile Shutter (97) AF area (93) Image size of movies (141) ISO sensitivity (109) 45 Display AWB Indication White balance (Auto, Preset, Custom, Color temperature, Color filter) (115) D-Range Optimizer (110)/Auto HDR (111) Creative Style (113) 7500K G9 Metering mode (108) Exposure compensation (104)/Metered Manual (82) Flash compensation (106) EV scale (82, 122) C Display 1/125 F2.8 +1.0 Indication Shutter speed (79) Aperture (76) Exposure (104) AE lock (103) SteadyShot (58) 46 Selecting a function/setting You can select a function for shooting or playback with the one of buttons, such as the Fn (Function) button, or the MENU button. When you start an operation, an operation guide of control button functions will be displayed at the bottom of the screen. : Press v/V/b/B on the control button to move the cursor. z: Press the center button to execute the selection. In this Instruction Manual, the process of selecting a function with the control button and the Fn button from the list displayed on the screen is described as follows (we explain the process with the default icons.): Before your operation Example: Fn button t AWB (White Balance) t Select the desired setting The operation guide list The operation guide also indicates operations other than the control button operation. The indications of icons are as follows. MENU button Returns with MENU button (Delete) button (Zoom in) button (Zoom out) button (Playback) button Control dial Help guide The Help Guide shows the information on a function selected with the Fn button, MENU button, etc. You can also turn it off (page 150). 47 Selecting a function with the Fn (Function) button This button is used for setting up or executing functions used frequently in shooting. 1 Press the Fn button. 2 Select the desired item with v/V/ b/B on the control button, then press the center z to execute. The setup screen appears. 3 Following the operation guide, select and execute the desired function. · For details on how to set up each item, see the corresponding page. Operation guide To set up the camera directly from the recording information screen Turn the control dial without pressing the center z in step 2. You can set up the camera directly from the recording information screen. 48 The functions selected by the Fn (Function) button SCN/Picture Effect (64, 67) Selects an appropriate mode from among the Scene Selection preset settings to suit shooting conditions, or an effect from among the Picture Effect filters. Sweep Shooting (69) Switches between Sweep Panorama and 3D Sweep Panorama. Drive Mode (119) Flash Mode (99) Sets the shooting mode to single-shot adv., continuous adv., self-timer, bracket shooting, etc. Sets the flash mode to Autoflash, Fill-flash, Flash Off, etc. Before your operation Autofocus Mode (92) Selects the method for focusing according to movement of the subject. AF area (93) Face Detection (96) Smile Shutter (97) ISO (109) Selects the area of focus. Automatically captures people's face(s) with the optimal focus and exposure. Camera shoots when a smile is detected. Sets the sensitivity to light. The larger the number, the faster the shutter speed. Adjusts the intensity of flash output. + direction increases brightness of subject, and the - direction increases darkness. Adjusts the color tone of images. Selects your desired image processing. Metering Mode (108) Selects the method for measuring brightness. Flash Compensation (106) White Balance (115) Creative Style (113) DRO/Auto HDR (110) Compensates for the brightness and contrast automatically. 49 The functions selected by the MENU button You can set up the basic settings for the camera as a whole or execute functions such as shooting, playback, or other operations. Press the MENU button, select the desired page with b/B on the control button, and select the desired item with v/V. Recording menu Image: Size (140) Image: Aspect Ratio (141) Movie: File Format (86) Movie: Size (141) Movie: Audio Rec. (87) SteadyShot (58) Selects the size of still images. Selects the aspect ratio for still images. Image: Quality (141) Sets the images quality f ...

Choose and compare

Choose your products (tick the boxes), then click on the "Compare" button.

SONY SLT-A35

the products that have already been seen :

OLYMPUS E-5

ZOOM 2020

MOTOROLA ATRIX

HTC DESIRE Z

ALCATEL OT-300

ACER ICONIA

LG LG 125

related products :

SONY SRS-A35

SONY PLM-A35

SONY SLT-A55VL

SONY SLT-A55

CANON EOS 550D

PENTAX K5

MOTOROLA ATRIX 4G

NIKON D3100

FUJIFILM FINEPIX HS20EXR

JVC GZ-HD520

High-performance	Reliability
Ease of use	Value for money